Neuspeed 65.10.97 Manual de usuario

Busca en linea o descarga Manual de usuario para Para El Coche Neuspeed 65.10.97. Neuspeed 65.10.97 User Manual [en] [de] [pl] Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 2
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
NEUSPEED® • 3300 Corte Malpaso • Camarillo, CA 93012 • 805.388.7171 • 805.388.0030 FAX • information@neuspeed.com • Visit us on the web…http://www.neuspeed.com
P-FLO AIR INTAKE KIT PART #65.02.65 & 65.10.97
Fits 2006-2008.5 Audi A3 2.0T FSI, 2008 TT(8J) 2.0T FSI, 2006-2008.5 VW EOS, GTI, Jetta V & Passat with 2.0T FSI
Only fits Passat models equipped with manual transmission
PARTS LIST: 65.02.65/65.10.97 TOOLS REQUIRED:
1 INTAKE PIPE 1 HEAT SHIELD 1 NEUSPEED FILTER 2 SS WASHER 1 T20 TOX 1 FLAT BLADE SCREW DRIVER 1 PHILIPS SCREWDRIVER
1 SILICONE HOSE 2 PHILIPS HEAD SCREWS M4x8mm 1 HEX SCREW M6x10mm 1 4mm HEX KEY WRENCH 1 SPRING CLAMP PLIERS 1 10MM WRENCH
1 RUBBER ISOLATOR 1 #40 CLAMP 1 #44 CLAMP 1 24mm 12 POINT SOCKET
1. Remove the intake air duct: There are
two T20 Torx screws that attach duct to
the front core and a spring clamp at
hose connection to the air filter box
(engine cover).
2. Disconnect electrical connector at MAF
(Mass Air Flow) sensor and remove
sensor mounting screws (T20 Torx),
now pull out sensor.
3. Unclip and disconnect turbo intake hose
from air filter box.
4. There are four rubber grommet mounts
holding air filter box (engine cover) to
engine. Lift up one corner of air filter
box at a time to detach.
5. Remove turbo intake hose at turbo by
squeezing spring clamp with spring
clamp pliers. CAUTION: Do not let any
debris or objects fall into turbo inlet or
damage may occur.
6. Installing NEUSPEED heat shield: First
remove the (2) 10mm hex nuts located
on bottom side of factory heat shield
connecting the rear air filter box (engine
cover) mounts. Then using a 24mm 12
point socket, unscrew the mounts.
7. Install NEUSPEED heat shield using
original air filter box mounts with SS
washers supplied. Then reinstall 10mm
hex nuts on bottom side.
8. Install silicone hose onto turbo side of
NEUSPEED intake pipe and tighten with
#44 clamp supplied. NOTE: Screw
clamp should be rotated toward
passenger side of vehicle.
Vista de pagina 0
1 2

Indice de contenidos

Pagina 1

NEUSPEED® • 3300 Corte Malpaso • Camarillo, CA 93012 • 805.388.7171 • 805.388.0030 FAX • [email protected] • Visit us on the web…http://www.neu

Pagina 2 - Copyright 2012, NEUSPEED

NEUSPEED® • 3300 Corte Malpaso • Camarillo, CA 93012 • 805.388.7171 • 805.388.0030 FAX • [email protected] • Visit us on the web…http://www.neu

Modelos relacionados 65.02.65

Comentarios a estos manuales

Sin comentarios